Introduction to Robotics/Electrical Components/Lecture/Teachers: Difference between revisions
wikademia>Whiteknight New page: {{Introduction to Robotics/Nav|Electrical Components}} == Electricity Flowing in a Circuit == Electricity flows through circuits in the same way as water flows through pipes. Water only ... |
wikademia>Dr. Eme m moved Beta:Introduction to Robotics/Electrical Components/Lecture/Teachers to Introduction to Robotics/Electrical Components/Lecture/Teachers over redirect |
||
| (16 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
{{ | == Electricity Flowing in a Circuit == | ||
{{ntnes}} | |||
Electricity flows through circuits in the same way as water flows through pipes. Water only flows where the pipes are properly connected. Likewise, electricity will only flow where the components and wires are properly connected. | |||
Notice also that electricity will only flow in a "'''complete circuit'''". Electricity must come from a source, and must go to a ground. | |||
There are two quantities that we need to measure when dealing with electricity: Voltage and Current. | |||
;Voltage:Voltage is a measure of the "pressure" of the electricity. More voltage means more potential for the electricity to flow. | |||
;Current:Current is a measure of the "amount" of the electricity. More current means more electrons are flowing. | |||
== Resistors: Resisting current == | == Resistors: Resisting current == | ||
Resistors are said to "resist current". At the same pressure (voltage), resistors cause less current to flow. Resistors are measured in units called "Ohms", and are labled with a Ω (greek capital omega). | |||
For the same pressure, more ohms means less current, and fewer ohms means more current. | |||
== Ohm's Law == | == Ohm's Law == | ||
The relationship between current, voltage, and resistance is shown by '''Ohm's Law''': | |||
:<math>V = IR</math> | |||
== Resistor Color Codes == | == Resistor Color Codes == | ||
{{Introduction to Robotics/Resistors}} | |||
Resistor values are shown using a special color code. A resistor will have 4 colored bands on it, one of the bands will be gold or silver. To read a resistor, put the gold/silver band on the right. The first two bands on the left are the digits, and the third band is an exponent. | |||
To calculate the value of a resistor, we take the first two digits to form a 2-digit number, and we multiply it by 10 to the power of the third band. For instance, if our resistor was: | |||
{{Introduction to Robotics/Resistor|red|green|yellow}} | |||
Then the value of the resistor would be: | |||
:<math>25 \times 10^4 = 250000 = 250k\Omega</math> | |||
The fourth band is a "tolerance" band, or an error code. Silver means the resistor has a 10% error, and gold means the resistor has a 5% error. | |||
{{-}} | |||
{{Introduction to Robotics/Visual|Resistor Color Codes}} | |||
== Diodes: 1-way Gates == | == Diodes: 1-way Gates == | ||
== Buttons == | == Buttons == | ||
Latest revision as of 19:24, 12 August 2009
Electricity Flowing in a Circuit
Electricity flows through circuits in the same way as water flows through pipes. Water only flows where the pipes are properly connected. Likewise, electricity will only flow where the components and wires are properly connected.
Notice also that electricity will only flow in a "complete circuit". Electricity must come from a source, and must go to a ground.
There are two quantities that we need to measure when dealing with electricity: Voltage and Current.
- Voltage
- Voltage is a measure of the "pressure" of the electricity. More voltage means more potential for the electricity to flow.
- Current
- Current is a measure of the "amount" of the electricity. More current means more electrons are flowing.
Resistors: Resisting current
Resistors are said to "resist current". At the same pressure (voltage), resistors cause less current to flow. Resistors are measured in units called "Ohms", and are labled with a Ω (greek capital omega).
For the same pressure, more ohms means less current, and fewer ohms means more current.
Ohm's Law
The relationship between current, voltage, and resistance is shown by Ohm's Law:
- <math>V = IR</math>
Resistor Color Codes
| 0 | |
| 1 | |
| 2 | |
| 3 | |
| 4 | |
| 5 | |
| 6 | |
| 7 | |
| 8 | |
| 9 |
Resistor values are shown using a special color code. A resistor will have 4 colored bands on it, one of the bands will be gold or silver. To read a resistor, put the gold/silver band on the right. The first two bands on the left are the digits, and the third band is an exponent.
To calculate the value of a resistor, we take the first two digits to form a 2-digit number, and we multiply it by 10 to the power of the third band. For instance, if our resistor was:
| red | green | yellow | gold |
Then the value of the resistor would be:
- <math>25 \times 10^4 = 250000 = 250k\Omega</math>
The fourth band is a "tolerance" band, or an error code. Silver means the resistor has a 10% error, and gold means the resistor has a 5% error.
| 0 | |
| 1 | |
| 2 | |
| 3 | |
| 4 | |
| 5 | |
| 6 | |
| 7 | |
| 8 | |
| 9 |
|
<math>25 \times 10^4 = 250000 = 250k\Omega</math> | ||||||||
|
<math>25 \times 10^4 = 250000 = 250k\Omega</math> | ||||||||
|
<math>25 \times 10^4 = 250000 = 250k\Omega</math> | ||||||||
|
<math>25 \times 10^4 = 250000 = 250k\Omega</math> | ||||||||
|
<math>25 \times 10^4 = 250000 = 250k\Omega</math> |
This page has not be categorized. You can help by giving it an appropriate category.