Concrete leveling: Difference between revisions
wikademia>Greeneba1 |
wikademia>Sgroupace |
||
| Line 4: | Line 4: | ||
{{Unreferenced|date=April 2007}} | {{Unreferenced|date=April 2007}} | ||
Concrete leveling is a procedure that attempts to correct uneven concrete | Concrete leveling is a procedure that attempts to correct an uneven concrete surface by altering the foundation that the surface sits upon. It is a cheaper alternative to having replacement concrete poured, and commonly performed at small businesses and private homes. | ||
Sidewalks, patios and garage floors are most often made of [[concrete]]. When the concrete is a few inches thick and poured on insufficient foundation and/or without steel reinforcement it may crack and subside. Sometime water run off from rain or flood can wash away dirt upon which the concrete slab is resting leading to cracking and subsiding. When that happens the concrete can be demolished and removed and then re-built, however a method called [[mudjacking]] or slabjacking can both raise the old cracked slab back to its original position and create a new [[foundation]] of [[cement]] [[Mortar (masonry)|mortar]] or [[sand mix]] by injecting the mortar under the slab through a hole, under pressure. The [[viscosity]] of the mortar will keep it from flowing back through the hole until it sets. For a diagram see [http://www.raise-rite.com/concrete_raising/how.html] | Sidewalks, patios and garage floors are most often made of [[concrete]]. When the concrete is a few inches thick and poured on insufficient foundation and/or without steel reinforcement it may crack and subside. Sometime water run off from rain or flood can wash away dirt upon which the concrete slab is resting leading to cracking and subsiding. When that happens the concrete can be demolished and removed and then re-built, however a method called [[mudjacking]] or slabjacking can both raise the old cracked slab back to its original position and create a new [[foundation]] of [[cement]] [[Mortar (masonry)|mortar]] or [[sand mix]] by injecting the mortar under the slab through a hole, under pressure. The [[viscosity]] of the mortar will keep it from flowing back through the hole until it sets. For a diagram see [http://www.raise-rite.com/concrete_raising/how.html] | ||
| Line 17: | Line 17: | ||
== External links == | == External links == | ||
[http://www.uretekicr.com] | [http://www.uretekicr.com] | ||
The newest method (developed by URETEK) in concrete leveling utilizes two part closed cell polymer expanding foam which is injected through a hole less than one inch in diameter, typically 5/8". Although the material injected at a higher psi rate than traditional cementious grouts the pressure is not what causes the lifting. The expansion of the injected material below the slab surface performs the actual lifting action. Material injected below a slab to be lifted will first find weak soils, expanding into them in such a manner as to consolidate and cause sub-soils to become more dense and fill any voids below the slab. One inherent property of expanding foams is that they will follow the path of least resistance, expanding in all directions. Another inherent property includes reaching a hydro-insensitive or hydrophobic state when cured with 100% cure times as little as 30 minutes. Closed cell polymer foams offer benefits which go beyond the goal of leveling hard surfaces. They will not retain moisture, which in northern climates can cause frost heaving. They are not subject to erosion once in place. Their fast cure time allows for immediate use when application is complete. Their light weight, 3 to 8 lbs. per cubic ft. vs. 100 to 120 lbs. per cubic ft. for cementious grout will not cause further settlement. Foams will retain their cured shape and volume indefinitely reducing the possibility of new voids forming below grade to nearly zero unless acted upon by some outside cause. Some closed cell polymer foams have baseline lifting capabilities of 6,000 lbs per sq. ft. and leveling procedures have been performed in which loads as high as 125 tons have been lifted and stabilized in a surface area of less than 900 sq. ft. | The newest method (developed by URETEK) in concrete leveling utilizes two part closed cell polymer expanding foam which is injected through a hole less than one inch in diameter, typically 5/8". Although the material injected at a higher psi rate than traditional cementious grouts the pressure is not what causes the lifting. The expansion of the injected material below the slab surface performs the actual lifting action. Material injected below a slab to be lifted will first find weak soils, expanding into them in such a manner as to consolidate and cause sub-soils to become more dense and fill any voids below the slab. One inherent property of expanding foams is that they will follow the path of least resistance, expanding in all directions. Another inherent property includes reaching a hydro-insensitive or hydrophobic state when cured with 100% cure times as little as 30 minutes. Closed cell polymer foams offer benefits which go beyond the goal of leveling hard surfaces. They will not retain moisture, which in northern climates can cause frost heaving. They are not subject to erosion once in place. Their fast cure time allows for immediate use when application is complete. Their light weight, 3 to 8 lbs. per cubic ft. vs. 100 to 120 lbs. per cubic ft. for cementious grout will not cause further settlement. Foams will retain their cured shape and volume indefinitely reducing the possibility of new voids forming below grade to nearly zero unless acted upon by some outside cause. Some closed cell polymer foams have baseline lifting capabilities of 6,000 lbs per sq. ft. and leveling procedures have been performed in which loads as high as 125 tons have been lifted and stabilized in a surface area of less than 900 sq. ft. | ||
[[Category:Concrete]] | [[Category:Concrete]] | ||